DJI Mavic Pro Firmware Release Notes

An ongoing archive of all firmware updates to the DJI Mavic Pro.

Remember: always run new firmware updates for each of your extra aircraft batteries, as the firmware package will often update these too.

http://www.dji.com/mavic/info#downloads

Changes Firmware Released Tested*
  • Added Pano shooting modes (requires DJI GO app v4.1.1.0 or higher).
  • Optimised GEO Zone management.
  • Optimised Intelligent Flight Battery firmware updating.
  • Improved flight performance when using propeller guards.
v01.04.0100 2017-11-23
  • Added QuickShot feature (requires DJI GO 4 app v4.1.10 or higher).
  • Added Dynamic Home Point for ActiveTrack mode (requires DJI GO 4 app v4.1.10 or higher).
  • Added support for Mavic Pro Platinum firmware and 8331 Low-Noise Quick Release Propellers.
  • Adjusted the colour in Normal mode to Vivid (requires DJI GO 4 app v4.1.10 or higher).
v01.04.0000 2017-09-19
  • Fixed an occasional issue where DNG files couldn’t be opened.
  • Fixed an occasional issue where the camera would restart automatically during recording.
  • Fixed an occasional issue where the gimbal would drift after self-checking.
  • Limited the max descend speed to 2 m/s and max ascend speed to 3 m/s in Propeller Cage mode. Improved image quality.
v01.03.1000 2017-08-22
  • Fixed DNG file white balance issues when shooting in Portrait mode.
v01.03.0900 2017-06-22
  • Updated No Fly Zone Management.
  • For increased safety, the flight is restricted to a height of 30 m and distance of 50 m when not connected or logged into the app during flight, including DJI GO 4 and all apps compatible with DJI aircraft.
  • Added gimbal control in Fixed-Wing.
  • Optimised colour shading in for improved footage quality.
  • Fixed minor drift issue in Portrait.
v01.03.0800 2017-06-08
  • Added support for DJI Goggles.
  • Optimized gimbal self checking
v01.03.0700 2017-05-09
  • Added Fixed-Wing mode. For details about Fixed-Wing mode, please refer to the Intelligent Flight Mode section in user manual v1.6.
  • Added an option to turn off the remote controller low battery level warning. When battery level is less than 15%, just press the power button on the remote controller to turn off the warning.
  • Optimized Dual Remote Controller Mode. (Requires DJI GO 4 iOS v4.0.5 or later or Android v4.0.5 or later)
  • Optimized No-Fly Zone Return to Home and unlocking function.
  • Improved playback performance.
  • Improved default colors for DNG files.
  • Optimized gimbal auto-calibration.
v01.03.0600 2017-04-11
  • Optimized the RTH function.
  • Improved hovering performance.
v01.03.0550 2017-05-05
  • Updated No-Fly Zone management.
  • Optimized gimbal calibration.
v01.03.0500 2017-03-02
  • Added a self-diagnostic test function for ultrasonic sensors every time the aircraft is powered on.
  • Improved the Interval Mode performance.
  • Upgraded the D-Log color mode to extend dynamic range.
  • Optimized the video transmission by reducing the transmission signal loss ratio.
v01.03.0400 2017-02-14
  • Improved gimbal performance when flying in low temperatures.
  • Added Cinematic Mode for smoother footage. [Jb: added? was already present]
v01.03.0200 2016-12-26
  • Added AR [sic: Augmented Reality] route display in TapFly mode when used with the DJI GO 4 app.
  • Added a vibration warning for the remote controller when the aircraft enters ATTI mode.
  • Added wind speed evaluation and a high wind speed warning.
  • Added more film looks and colour modes (when used with the DJI GO 4 app).
  • Optimised the compass algorithm to reduce switching from GPS Mode to ATTI Mode.
  • Improved magnetic detection for the remote controller. The aircraft will now return to home when strong magnetic interference is detected.
  • Improved the speed at which the HD video link connection can be regained after disruption.
  • Optimised altitude maintenance capabilities when flying over water.
  • Optimised Gesture Mode.
  • Improved the indoor flying experience by shortening the minimum distance from an obstacle from 3m to 1m.
  • Optimised power management for long-term battery storage.
v01.03.0000 2016-12-06
  • Optimised Remote Controller Calibration.
  • Adjusted default gimbal pitch smoothing value from 10 to 15 for smoother movement.
  • Increased USB connection stability.
  • Adjusted camera colour.
  • Fixed occasional remote control command timeout.
  • Fixed occasional unresponsiveness to remote controller commands.
  • Deleted support for using C1 or C2 button to launch the DJI GO app on iOS.
v01.02.0900 2016-11-09
  • Optimised the Return-to-Home and Landing (refer to the user manual for details).
  • Reduced descent issue caused from flying indoors to outdoors.
  • Minimised an overheating issue resulting from not removing the gimbal clamp after powering on the aircraft.
  • Improved the stability of the aircraft when switching between Portrait and Landscape.
  • Optimised the ActiveTrack experience, keeping moving subjects in center frame more effectively and smoothing footage.
  • Optimised control parameters to improve the flight experience.
  • Fixed occasional issue of GPS signal loss.
v01.02.0800 2016-10-21

*Tested with my own Mavic Pro and running ok.

SUBSCRIBE FOR FRESH CONTENT

Follow me on social media for updates.